PRC-Saltillo sells the Via line of devices. The keyguard designer supports these tablets, but we don’t know anything about the measurements of the case opening or possible mounting methods. If you have one of these devices and would like to help us provide that information to everyone else, go to the Contact Us page and let us know.

Via Pro

Uses an iPad Pro 11-inch 2nd Generation as its tablet.

Via Mini

Uses an iPad Mini 6 as its tablet.

Via Nano

Uses an iPhone 15 as its tablet.

Versa

The Versa line of products is, fundamentally, a collection of tablet cases and accessories for these cases. These cases are based on various iPad Models.

The VersaWrap 8.1 is compatible with iPad mini® 6th Gen and iPad mini (A17 Pro).
The VersaWrap 10.1 is compatible with iPad 7th, 8th, 9th, 10th Gen, iPad Air® 4th, 5th Gen, iPad Pro® 11 1st, 2nd, 3rd, 4th Gen, iPad Air 11-inch (M2), iPad Pro 11-inch (M4), and iPad 11-inch (A16).
The VersaWrap 12.1 is compatible with the iPad Pro 12.9 (3rd, 4th, 5th, and 6th Gen), iPad Air 13-inch (M2), and iPad Pro 13-inch (M4).
The VersaEye adds eye tracking to one of the above configurations.

VersaWrap 8.1

VersaWrap 10.1

As you can see above, the VersaWrap case fits a number of iPads. The resources below are specifically designed for the iPad Pro 11.

Thanks to Cynthia Heryanto for getting these measurements and designing these keyguards for the iPad Pro 11, 1st, 2nd, 3rd, and 4th generation. Note that Cynthia chose to design these keyguards as a keyguard/frame combination. That way, she was able to take advantage of the “posts” connection between the keyguards and the frame.

Note that the single keyguard frame STL file below will work with any of the keyguard STL files.

If you’d like to modify or extend these designs, you might benefit from these important Customizer setting values:

---- Tablet ----
type_of_tablet = "iPad Pro 11-inch 3rd Generation"

---- Tablet Case ----
height_of_opening_in_case = 169
width_of_opening_in_case = 236
left_edge_compensation_for_tight_cases = 10
right_edge_compensation_for_tight_cases = 10

---- App Layout in px ----
bottom_of_status_bar = 10
bottom_of_upper_message_bar = 185
bottom_of_upper_command_bar = 260
top_of_lower_message_bar = 1616
top_of_lower_command_bar = 1668

---- Grid Special Settings ----
cell_edge_slope = 85
top_padding = 0.8
bottom_padding = -0.8
left_padding = 5.4
right_padding = 5.4

---- Mounting Method ----
mounting_method = "Slide-in Tabs"

---- Slide-in Tabs Info ----
slide_in_tab_locations = "horizontal and vertical"
preferred_slide_in_tab_thickness = 1
horizontal_slide_in_tab_length = 10
vertical_slide_in_tab_length = 10
vertical_slide_in_tab_width = 50

---- Keyguard Frame Info ----
have_a_keyguard_frame = "yes"
keyguard_frame_thickness = 4
keyguard_width = 225
mount_keyguard_with = "posts"
snap_in_tabs_on_left_and_right_edges_of_keyguard = "no"

---- Special Actions and Settings ----
keyguard_edge_chamfer = 0.7
cell_edge_chamfer = 0.7

The “App layout in px” values assume that you’re designing for a Unity layout. You’ll need to determine the proper values for the options in the “Grid Info” section based on the layout of your particular layout.

The standard openings_and_additions.txt file can be used with these settings.