(link to SUPCASE case on Amazon)
Like all cases with screen protectors, there’s very little room between the inner edges of the screen protector and the edges of the screen. This places limitations on what can be done with a keyguard as well as the mounting methods. We’ve opted to use raised tabs as the mounting method for this case.
To choose and download your keyguard design:
- Find your app in the first column.
- Find the layout for your app in the second column.
- You can get an idea what your keyguard will look like by clicking on the “image” link in that row.
- Click on the “STL” link to download your design.
- Once you’ve printed your design, look at the links at the bottom of the page for instructions on how to mount your keyguard.
| AAC App | Layout | Approx. Print Cost & Time | Mounting Method |
|
| raised tabs | raised tabs w/ magnets | |||
| P2G | 6 x 10 | $1.44 5h 29m |
STL / image | STL |
| 7 x 11 | $1.16 5h 7m |
STL / image | STL | |
| Proloquo | fixed | $1.06 5h 12m |
STL / image | STL |
| CoughDrop | QC 60 | $1.45 5h 22m |
STL / image | STL |
| QC 112 | $1.06 4h 45m |
STL / image | STL | |
| Grid for iPad | SC 30 | $1.18 4h 45m |
STL / image | STL |
| SC 30 max rails* |
$2.22 6h 42m |
STL / image | STL | |
| SC 50 | $1.29 5h 59m |
STL / image | STL | |
| Voco Chat | $1.11 4h 12m |
STL / image | STL | |
| LWFL | 7 x 12 | $1.22 5h 18m |
STL / image | STL |
| LWFL – VI** | 7×12 | $1.91 6h 59m |
STL / image | STL |
| S4Y | 8 x 15 | $0.75 4h 18m |
STL / image | STL |
| TD Snap | 5 x 5 MP 30 |
$0.97 3h 47m |
STL / image | STL |
| 5 x 5 MP 30 max rails |
$1.42 6h 10m |
STL / image | STL | |
| MP 66 | $0.97 3h 47m |
STL / image | STL | |
| 8 x 10 | $1.03 5h 50m |
STL / image | STL | |
| TouchChat | WP42 | $1.31 5h 16m |
STL / image | STL |
| WP42 (font size 72) | $1.31 5h 16m |
STL / image | STL | |
| WP60 | $1.46 5h 55m |
STL / image | STL | |
| WP60 (font size 72) | $1.46 5h 55m |
STL / image | STL | |
| WP80 | $1.43 5h 58m |
STL / image | STL | |
| WP80 (font size 72) | $1.43 5h 58m |
STL / image | STL | |
| WP108 | $1.31 5h 39m |
STL / image | STL | |
| WP108 (font size 72) | $1.31 5h 39m |
STL / image | STL | |
| WP108 (merged) |
$1.31 5h 39m |
STL / image | STL | |
| WP108 (merged) (font size 72) | $1.31 5h 39m |
STL / image | STL | |
* same as SC 30 layout, just with the rails as wide as possible and slightly taller
** outer landmarks are implemented as bumps rather than horizontal and vertical ridges
Note that the “Approx. Print Cost & Time” figures below only apply if you are printing the keyguard for yourself. When the case supports multiple mounting methods we’ve estimated the cost for the most expensive of the mounting methods. Note that we’ve had success printing keyguards using PLA filament with a 15% infill, two perimeters, and 4 top/bottom layers. Print Costs assume a $20 roll of filament. All keyguards with raised tabs should be printed with supports.
Mounting Your Keyguard
Refer to these pages based on your choice of mounting method for a description of how to mount your keyguard: